Recycled aluminum alloys offer large energy savings, yet accumulated impurities, particularly iron, often reduce strength and ductility. This article examines how thermomechanical processing influences the mechanical properties of a recycled Al–Mg–Si alloy. A processing matrix combining three hot-deformation temperatures (400, 450 and 500 °C) and two thickness reductions (30% and 60%), followed by solution treatment and artificial aging, is evaluated through tensile testing, Vickers hardness, electron backscatter diffraction and two-way analysis of variance. Because no verified laboratory dataset is available, the quantitative results are explicitly hypothetical scenario values, not measurements. They illustrate how lower deformation temperature and larger reduction refine grains and raise strength, whereas higher temperature favors ductility through fragmentation of iron-rich particles. The framework supports reproducible experimental validation and informs industrial processing of recycled wrought aluminum.
Investigation of The Effect of Thermomechanical Processing on The Mechanical Properties of Recycled Aluminum Alloys
DOI:
Abstract
References
D. Raabe et al., “Making sustainable aluminum by recycling scrap: The science of ‘dirty’ alloys,” Prog. Mater. Sci., vol. 128, Art. 100947, 2022, doi: 10.1016/j.pmatsci.2022.100947.
H. Nunes, O. Emadinia, R. Soares, M. F. Vieira, and A. Reis, “Adding value to secondary aluminum casting alloys: A review on trends and achievements,” Materials, vol. 16, no. 3, Art. 895, 2023, doi: 10.3390/ma16030895.
S. Capuzzi and G. Timelli, “Preparation and melting of scrap in aluminum recycling: A review,” Metals, vol. 8, no. 4, Art. 249, 2018, doi: 10.3390/met8040249.
R. Lin, B. Liu, J. Zhang, and S. Zhang, “Microstructure evolution and properties of 7075 aluminum alloy recycled from scrap aircraft aluminum alloys,” J. Mater. Res. Technol., vol. 19, pp. 354–367, 2022, doi: 10.1016/j.jmrt.2022.05.011.
D. De Caro et al., “Effect of recycling on the mechanical properties of 6000 series aluminum-alloy sheet,” Materials, vol. 16, no. 20, Art. 6778, 2023, doi: 10.3390/ma16206778.
J. Krolo, B. Lela, I. Dumanić, and F. Kozina, “Statistical analysis of the combined ECAP and heat treatment for recycling aluminum chips without remelting,” Metals, vol. 9, no. 6, Art. 660, 2019, doi: 10.3390/met9060660.
D. Bösch et al., “Secondary Al-Si-Mg high-pressure die casting alloys with enhanced ductility,” Metall. Mater. Trans. A, vol. 46, no. 3, pp. 1035–1045, 2015, doi: 10.1007/s11661-014-2700-8.
S. Ferraro, A. Bjurenstedt, and S. Seifeddine, “On the formation of sludge intermetallic particles in secondary aluminum alloys,” Metall. Mater. Trans. A, vol. 46, pp. 3713–3722, 2015, doi: 10.1007/s11661-015-2942-0.
J. Kasińska, D. Bolibruchová, and M. Matejka, “The influence of remelting on the properties of AlSi9Cu3 alloy with higher iron content,” Materials, vol. 13, no. 3, Art. 575, 2020, doi: 10.3390/ma13030575.
A. E. Salas Reyes et al., “Microstructural, microscratch and nanohardness mechanical characterization of secondary commercial HPDC AlSi9Cu3-type alloy,” J. Mater. Res. Technol., vol. 9, pp. 8266–8282, 2020, doi: 10.1016/j.jmrt.2020.05.098.